CCNA 2 Practice Final Exam 2013

Screenshot - 04.03.2013 , 23_31_48

1. Refer to exhibit .The network is using the RIPv2 routing protocol.If network 10.0.0.0 goes down ,what mechanism will prevent Router1 from advertisting false routing information back to Router2?

triggered updates

poison reverse

holddown timers

split horizon

2

2.Refer to exhibit.All routers are advertised and fully operational on all routers.Which statement is true about the path that the data will take from router A to router B?

if EIGRP is used with default configuration , the data will be equally distributed between two paths – A,D,B and A,C,B

if RIPv1 is  used with default configuration , the data will be load-balanced on all paths

if EIGRP and OSPF are both used with default configuration ,the data will be sent through paths learned by the OSPF protocol

if RIPv2 is  used with default configuration , the data will be equally distributed between two paths – A,D,B and A,C,D

Screenshot - 04.03.2013 , 23_31_56

3.Refer to exhibit.Based on the output from the show running-config and debug ip rip commands ,what are two of the routes that are added to the routing table of R1?(choose two)

R 192.168.1.0/24[120/1] via 172.16.2.1 ,00:00:24 ,Serial0/0/1

R 192.168.1.00/24[120/1] via 172.16.1.1 ,00:00:24 ,Serial0/0/0

S 192.168.1.0/24[1/0] via FastEthernet0/0

R 192.168.2.0/24[120/1] via 172.16.1.2 ,00:00:24 ,Serial0/0/0

Screenshot - 04.03.2013 , 23_31_56

4.Refer to the exhibit.What summarization should R2 use to advertise its LAN networks to R1?

172.16.0.0/24

172.16.4.0/22

172.16.4.0/23

172.16.4.0/24

Screenshot - 04.03.2013 , 23_32_02

5.Refer to the exhibit.The network administrator is planning IP addressing of a new network .What part of this addressing scheme must be changed to allow communication between hostA and the server?

the IP address of the server

the default gateway of host A

the IP address of host A

the default gateway of the server

Screenshot - 04.03.2013 , 23_32_02

6.Refer to the exhibit.Two routers are unable to establish an adjacency.What is possible cause for this?

the two routers are connected on a multiaccess network

the hello and dead intervals are different on the two routers

they have different OSPF router IDs

they have different process IDs

7.What are two functions of a router?(choose two)

it connects multiple IP networks

it control the flow of data via the use of Layer 2 addresses

it determines the best path to send packets

it manages the VLAN database

it increases the size of the broadcast domain

Screenshot - 04.03.2013 , 23_32_10

8.Refer to the exhibit.A network designer is testing a prototype of WAN connection.All of the routers in the exhibit are configured for OSPF routing.The design requires that the path between routers A and D through ISP-A is the primary and the path through ISP-B serves as a backup. The designer notice that  router A has two equal-cost paths to the LAN on router D. How can the designer correct this problem?

issue a clock rate 2000000 interface command on S0/0/1 of router ISP-B

change the default OSPF reference bandwidth on router A

configure two static routes with administrative distance of 10

use the bandwidth command to change the default bandwidth on the link to router ISP-B

Screenshot - 04.03.2013 , 23_32_17

9.Refer to the exhibit.Host A is having problems accessing server A .All routers have the same EIGRP configuration as router RTR-A.What should be done so that host A can access server A?

add the command no auto-summary on all routers

change the network statements to include a wildcard mask

adjust the EIGRP hello timers to account for the network delay

add the command eigrp log-neighbor-chances on all routers

Screenshot - 04.03.2013 , 23_32_17

10.Refer to the exhibit.The routers are properly configured using a dynamic routing protocol with default settings ,and the network is fully converged. Router A is forwarding data to router E.Which statement is true about the routing path ?

if the network use the RIP protocol , router A will determine that all the paths have equal cost

if the network use the RIP protocol , router A will update only the A-C-E path in its routing table

if the network use the EIGRP protocol , router A will determine that path A-D-E has the lowest cost

if both RIP and EIGRP protocols are configured on router A ,the router will use the route information that is learned by the RIP routing protocol

11.A sniffer program has captured a packet with a destination IP address of 224.0.0.10. Which protocol uses IP address?

RIP

RIPv2

OSPF

EIGRP

Screenshot - 04.03.2013 , 23_32_25

12.Refer to the exhibit. The show cdp neighbors command was run at  R1. Which two facts about the newly detected device can be determined from the output?(choose two)

ABCD is a router that is connected to R1

ABCD is non-CISCO device that is connected to R1

the device is connected at the Serial0/0/1 interface of R1

R1 is connected at the S0/0/1 interface of device ABCD

ABCD does not support switching capability

13.A router has learned about a network through static and dynamic routing processes.Which route will be used to reach network 192.168.168.0 ?

D 192.168.168.0/24[90/2195456] via 192.168.200.1 , 00:00:09 ,Ethernet0

O 192.168.168.0/24[90/1012] via 192.168.200.1 , 00:00:22 ,Ethernet0

R 192.168.168.0/24[120/1] via 192.168.200.1 , 00:00:17 ,Ethernet0

S 192.168.168.0/24[1/0] via 192.168.200.1

Screenshot - 04.03.2013 , 23_32_25

14.Refer to the exhibit.To implement the RIPv2  protocol ,the network administrator runs the command as displayed.However, the show ip protocols  command fails to display any output.How can the administrator solve the problem that is indicated by the lack of output from this command?

include the default-information originate command

include the auto-summary command

specify the network for which RIP routing has to be enabled

implement RIPv2 authentication in the network

15.What is one function of the bootstrap program during the router boot process?

loading Cisco IOS software

testing the router hardware

verifying the size of available RAM and flash

executing the commands in the configuration file

16.What is the advantage of configuring a static route with an exit interface instead of a next-hop address?

the router will perform a recursive lookup

this router will  automatically be used as the gateway of last resort

the next interface configuration consumes less router processing time

the exit interface configuration has an administrative distance value of 1

Screenshot - 04.03.2013 , 23_32_37

17.Refer to the exhibit.What destination address will RTB use to advertise LSAs?

224.0.05

224.0.0.6

10.1.7.17/28

172.16.1.1

172.16.2.1

255.255.255.255

Screenshot - 04.03.2013 , 23_32_37

18.Refer to the exhibit. What happens to a packet that has 172.16.0.0/16 as the best match in the routing table that is shown?

the packet is discarded

the packet is flooded out all interfaces

the packet is forwarded via Serial 0/0/0

the packet is forwarded via Fast Ethernet 0/0

Screenshot - 04.03.2013 , 23_32_45

19.Refer to the exhibit .R2 is configured correctly.The network administrator has configured R1 as shown. Which two facts are true about the forwarding of route information by R1 ?(choose two)

R1 will forward the route information for subnet 192.168.100.0/30

R1 will not forward the route information for subnet 192.168.100.4/30

R1 will forward the route information with an administrative distance set to 50 

R1 will forward the summarized route information for network 192.168.100.0/24

R1 will forward the route information for subnet 10.10.10.0/30 out the serial interface

20.A network is configured with the IP,IPX  and Apple Talk protocols. Which routing protocol is recommended for this network?

RIPv1

RIPv2

EIGRP

OSPF

Screenshot - 04.03.2013 , 23_32_45

21.Refer to the exhibit.What information can be determined from the displayed output?

EIGRP packets are waiting to be sent to the neighbors

the adjacencies between the routers are yet to be established

the IP address 192.168.10.10 is configured at serial interface S0/0/1 of router R2

router R2 is receiving hello packets from neighbor with the IP address 192.168.10.10 via the R2 S0/0/1 interface 

22

22.Refer to the exhibit. What needs to be done to allow these two routers to connect successfully ?

add a clock rate to S 0/0/0 on R1 

add an interface description to S 0/0/1 on R2

change the serial interface on R2 to S 0/0/0 so that is matches R1

change the IP address of S0/0/1 on R2 so that it is the same subnet as R1

23

23.Refer to the exhibit.All routers are running RIPv1 .The two networks 10.1.1.0/29 and 10.1.1.16/29 are unable to access ech other.What can be the cause of this problem?

because RIPV1 is a classless protocol ,it does not support this access

RIPv1 does not support discontiguous networks

RIPv1 does not support load balancing

RIPv1 does not support automatic summarization

24

24.Refer to the exhibit.A network technician notes that there are missing EIGRP routes in the routing tables on each router in this network.Based on the exhibited output ,what caused these missing routes?

the holdtime values are mismatched

the autonomous system number are mismatched

the interface on the link between RouterC and RouterD are shut down

an EIGRP neighbor relationship has not been established between Router A and RouterB

25

25.Refer to the exhibit.A network administrator has configured R1 as shown,and all interfaces are functioning correctly.Aping from R1 to 172.16.1.1 fails.What could be the cause of this problem?

the serial interface on R1 is configured incorrectly

the default route is configured incorrectly 

the default-information originate command must be issued on R1

autosummarization must be disabled on R1

26

26.Refer to the exhibit .R1 and R2 are unable to establish an adjacency .What two configuration changes will correct the problem?(choose two)

set lower priority on R2

configure the routers in the same area

set a lower cost on R2 compared to R1

add a backup designed router to the network

match hello and dead timers on both routers

27

27.Refer to the exhibit .How many routes are child routes?

1

2

4

6

28

28.Refer to the exhibit.A network administrator has run the show interface command .The output of this command is displayed.What is the first step that is required to make this interface operational ?

switch the cable with a know working cable

issue the  no shutdown command on the interface

configure the interface as a loopback interface

set the encapsulation for the interface

29.Using default settings ,what is the next step in the router boot sequence after the IOS loads from flash?

perform the POST routine

search for a backup IOS in ROM

load the running-config file from RAM

locate and load the startup-config file from NVRAM

30

30.Refer to the exhibit .R1 knows two routes,Path A and Path b,to the Ethernet network attached to R3. R1 learned Path A to network 10.2.0.0/16 from static route and Path B to network 10.2.0.0/16 from EIGRP. Which route will R1 install in its routing table?

both routes are installed and load balancing occurs both paths

the route via Path B is installed because EIGRP route has the best metric to network 10.2.0.0/16

the route via Path A is installed because the static  route has the best metric to network 10.2.0.0/16

the route via Path B is installed because EIGRP route has the lowest administrative distance  to network 10.2.0.0/16

the route via Path A is installed because the static  route has the lowest administrative distance  to network 10.2.0.0/16

 

31

31.Refer to the exhibit.What information can be determined from the highlighted output?

R1 is originating the route 172.30.200.32/28

automatic summarization is disabled

the 172.30.200.16/28 network is one hop away from R1

a classful routing protocol is being used

32

32.Refer to the exhibit.A new PC was deployed in the Sales network. It was given the host address 192.168.10.31 with a default gateway of 192.168.10.17 . The PC is not communicating with the network properly. What is the cause?

the default gateway is incorrect

the address is in the wrong subnet

the host address and default gateway are swapped

162.168.10.31 is the broadcast address for this subnet

33

33.Refer to the exhibit.A ping between host A and host B is successful ,but pings from host A to operational hosts on the Internet fail. What is the reason for this problem?

the Fast Ethernet interface of R1 is disabled

one of  the default routes is configured incorrectly

a routing protocol in not configured on both routers

the default gateway has not been configured on host A

34.A network administrator needs to assign the very last usable IP address in the 172.24.64.0/18 network range to the router interface that serves this LAN. Which IP address should the administrator configure on the interface ?

172.16.128.154/18

172.16.225.254/18

172.24.64.254/18

172.24.127.254/18

35.Which phase of the router process involves running diagnostics on the hardware components from ROM?

performing the POST

loading the bootstrap program

locating and loading the Cisco IOS software

locating and loading the startup configuration file

36

36.Refer to the exhibit.Router R2 is configured properly and all interfaces are functional.Router R1 has been installed recently . Host A is unable to ping host B.

Which procedure can resolve this problem?

configure a static route on R1 using the IP address of the serial interface on R1

configure a default route on R1 with the exit interface Fa0/0 on R1

configure static route on R1 using IP address of S0/0/0 on R2

configure a default route on R1 using the IP address of Fa0/0 on R2

37

37.Refer to the exhibit.The IP addresses on all interfaces on router R1 were configured before the OSPF protocol had been enabled on the router. No OSPF router ID was manually configured. Which IP address will be selected by the router as an OSPF router ID?

10.10.10.1

172.16.1.1

172.16.2.1

192.168.1.1

192.168.100.1

38.Which two situation required the use of a link-state protocol?(choose two)

fast convergence of the network is critical

the network is very large 

the network administrator has limited knowledge to configure and troubleshoot routing protocols

the network is a flat network

that capacity of the router is low

39

39.Refer to the exhibit. The network has three connected routers : R1,R2 and R3. The routers are displayed . All routers are operational and pings are not blocked on this network.

Which ping will fail?

from R1 to 172.16.1.1

from R1 to 192.168.3.1

from R2to 192.168.1.1

from R2 to 192.168.3.1

40.What is the function of the OSPF LSR packet ?

it is used to confirm the receipt of LSUs

it is used to established and maintain adjacency with other OSOF routers

it is used by receiving routes to request more information about entry in the DBD

is is used to check the database synchronization between routers

41

41.Refer to the exibith .A network administrator has configured OSPF using the following command :

network 192.168.1.32 0.0.0.31 area 0

Which router interface will participate in OSPF?

FastEthernet 0/0

FastEthernet 0/1

Serial 0/0/0

Serial 0/0/1

42

42.Refer to the exhibit. R1 and R2 are adjacent routers both running RIP. All interfaces on both routers are correctly configured and operational. Both routers are configured to include all connected interface in routing updated. R2 is not  showing any routes from R1 in the routing table. What is the likely cause ?

the adjacent interface are passive

the distance of 120 exceeds 15 hops

R2 will not accept version 1 updates from R1

routes are being summarized by R1 but not by R2

43

43.Refer to the exhibit. What is the meaning of the highlighted value 2?

it is the administrative distance of the routing protocol

it is the number of hops between R2 and the 192.168.8.0/24 network

it is the value used by the DUAL algorithm to determine the bandwidth for the link

it is the convergence time measured in secounds

44.A router has EIGRP configured as the only routing protocol. In what way might EIGRP respond if there is no feasible successor route to a destination network and the successor route fails?

it broadcast hello packets to all routers in the networks to re-establish neighbor adjacencies

it sends queries to adjacent neighbors until a new successor route is found

it immediately sends its entire routing table to its neighbors

it will set the metric for the failed route to infinity

45.A network technician must reduce the amount of broadcast traffic on the network while maintaining full connectivity between all different network segments. Which device should administrator deploy?

hub

router

Layer 2 switch

multiport repeater

46.Which port should a terminal emulator be connected to in order to access a router without network connectivity?

T1

serial

console

FastEthernet

47

47. Refert to the exhibit .The network administrator issue the command no ip classless on Router1. What forwarding action will take place on a packet that is received by Router 1 and is destined for host 192.168.0.26?

the packet will be dropped

the packet will be forwarded to the gateway of last resort

the packet will match the 192.168.0.0 network and be forwarded out Serian 0/0

the packet will most closely match the 192.168.0.8 subnet and be forwarded out Serial 0/1

48. The network shown in the diagram is having problems routing traffic. It is suspected that the problem is with the addressing scheme. What is the problem with the addressing used in the topology ?

the address assigned to the Ethernet 0 interface of Router1 is a broadcast address for that subnetwork

the subnetwork configured on the serial link between Router1 and Router2 overlaps with the subnetwork assigned to Ethernet 0 of Router3

the subnetwork assigned to the Serian 0 interface of Router1 is on a different subnetwork from the address for Serial 0 of Router2

the subnetwork assigned to Ethernet 0 of Router2 overlaps with the subnetwork assigned to Ethernet 0 of Router 3

49.What are two advantage of using a loopback interface on a router with OSPF enabled?(choose two)

a loopback interface has a much lower OSPF cost value by default

a loopback interface provides a stable ID because the loopback interface cannot be shutdown

a network administrator has more control over DR/BDR election by using a loopback interface over a physical interface

a loopback interface can be configured with higher bandwidth value that can a physical interface

a loopback interface address overrides any physical interface address or configured router-id value

50

50. Refer to the exhibit . Routers R1 and R3 use different routing protocols with default administrative distance values. All devices are properly configured and the destination network is advertised by both protocols.

Which path will be used to transmit the data packet between PC1 and PC2?

the packet will travel via R2-R1

the packet will travel via R2-R3

the packet will be load -balanced between two paths  - via R2-R1 and via R2-R3

the packet will travel via R2-R3 , and the other path via R2-R1 will be retained as the backup path.

This entry was posted in Uncategorized. Bookmark the permalink.

51 Responses to CCNA 2 Practice Final Exam 2013

  1. kd says:

    nice info. :)

  2. kd says:

    i think there is some mistakes ?
    is it wright ?

    • Tealeaf says:

      For 37, I think the answer should be the first one, because 10.10.10.1 is a loopback address and OSPF gives election priority to loopback.

      37.Refer to the exhibit.The IP addresses on all interfaces on router R1 were configured before the OSPF protocol had been enabled on the router. No OSPF router ID was manually configured. Which IP address will be selected by the router as an OSPF router ID?

      ******10.10.10.1

      172.16.1.1

      172.16.2.1

      192.168.1.1

      192.168.100.1

  3. tim says:

    is this the final exam for april 2013

  4. Margesh says:

    Can you send links for April 2013′s final exam? Please hurry~~!! thnx in advance!!

  5. Margesh says:

    Reply soon

  6. Sarah says:

    We have decided to open our POWERFUL and PRIVATE web traffic system to the public for a limited time! You can sign up for our UP SCALE network with a free trial as we get started with the public’s orders. Imagine how your bank account will look when your website gets the traffic it deserves. Visit us today: http://voxseo.com/traffic/

  7. dfvdfv says:

    100% ???

  8. goshua says:

    helloo! this is ERouting(second step of CCNA) final answers??

  9. goshua says:

    zeuxid thans very much!.. if its real answers its very help me!..

  10. silvia says:

    I passe with 90%

  11. Greg says:

    Are you sure this is right? i’ve found another version of the practice exam so I don’t know which to use :/ my exam is tomorrow :/

  12. goshua says:

    answers 16 it’s no wright

  13. goshua says:

    answer 17 wrong

  14. goshua says:

    zeuxid! thank you very very very much!!! to day I take 99%! I’ happy and thank you for this!

  15. lamqta says:

    Please send me those links. Thanks.

  16. acne says:

    Thank you a lot for giving everyone an very superb chance to study from this blog. It is always extremely pleasurable and packed with amusement for me and my office colleagues to visit your web site more than thrice every week to see the latest stuff you’ve got. And lastly, we are at all occasions fascinated with your extremely good ideas served by you. Some 4 points in this posting are particularly the extremely best I’ve ever had.

  17. Lindile says:

    Version 4 please!!ASAP

  18. big jeff says:

    very nice! thank you!
    i’ve been searching the web for the case study scripts or answers and couldnt find anything. is there someone that can help me out? where can i find these? i tried google and duckduck go and come up with other case studies but not the one im working on!! PLEASE HELP!!!

  19. gushua says:

    zeuxid do you have switching answers?

  20. marco says:

    Zeudix i want to tell you that my version is 4.0: will help me this answers??

  21. Andrew says:

    Are there good for June 2013?

  22. Nepoviem123 says:

    Is this practice test CCNA 2 ? 100% ?

  23. joadebanjo says:

    The CCNA exams has beed upgraded…the questions and answer are totally different

  24. Corrections…..
    3.Refer to exhibit.Based on the output from the show running-config and debug ip rip commands ,what are two of the routes that are added to the routing table of R1?(choose two)
    R 192.168.1.0/24[120/1] via 172.16.2.1 ,00:00:24 ,Serial0/0/1
    R 192.168.1.00/24[120/1] via 172.16.1.1 ,00:00:24 ,Serial0/0/0
    *****S 192.168.1.0/24[1/0] via FastEthernet0/0
    R 192.168.2.0/24[120/1] via 172.16.1.2 ,00:00:24 ,Serial0/0/0

    16.What is the advantage of configuring a static route with an exit interface instead of a next-hop address?
    the router will perform a recursive lookup
    this router will automatically be used as the gateway of last resort
    ****the next interface configuration consumes less router processing time
    the exit interface configuration has an administrative distance value of 1

    17.Refer to the exhibit. What destination address will RTB use to advertise LSAs?
    224.0.05
    ****224.0.0.6
    10.1.7.17/28
    172.16.1.1
    172.16.2.1
    255.255.255.255

    19.Refer to the exhibit. R2 is configured correctly. The network administrator has configured R1 as shown. Which two facts are true about the forwarding of route information by R1 ?(choose two)
    ****R1 will forward the route information for subnet 192.168.100.0/30
    ****R1 will not forward the route information for subnet 192.168.100.4/30
    R1 will forward the route information with an administrative distance set to 50
    R1 will forward the summarized route information for network 192.168.100.0/24
    R1 will forward the route information for subnet 10.10.10.0/30 out the serial interface

    37.Refer to the exhibit.The IP addresses on all interfaces on router R1 were configured before the OSPF protocol had been enabled on the router. No OSPF router ID was manually configured. Which IP address will be selected by the router as an OSPF router ID?
    ****10.10.10.1
    172.16.1.1
    172.16.2.1
    192.168.1.1
    192.168.100.1

    45.A network technician must reduce the amount of broadcast traffic on the network while maintaining full connectivity between all different network segments. Which device should administrator deploy?
    hub
    ****router
    Layer 2 switch
    multiport repeater

    • aghist says:

      Thank you! But for the third answer I think that also the first entry is correct, the 192.168.1.0 route learned by rip.

  25. nene says:

    What is the advantage of configuring a static route with an exit interface instead of a next-hop address?
    The router will perform a recursive lookup.
    This route will automatically be used as the gateway of last resort.
    ***The exit interface configuration consumes less router processing time.
    The exit interface configuration has an administrative distance value of 1.

    A network technician must reduce the amount of broadcast traffic on the network while maintaining full connectivity between all different network segments. Which device should the administrator deploy?
    hub
    ***router
    Layer 2 switch
    multiport repeater

    Refer to the exhibit. Based on the output from the show running-config and debug ip rip commands, what are two of the routes that are added to the routing table of R1? (Choose two.)
    R 192.168.1.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/1
    ***R 192.168.100.0/24 [120/1] via 172.16.1.1, 00:00:24, Serial0/0/0
    ***S 192.168.1.0/24 [1/0] via FastEthernet0/0
    R 192.168.9.0/24 [120/1] via 172.16.2.1, 00:00:24, Serial0/0/0
    R 192.168.2.0/24 [120/1] via 172.16.1.2, 00:00:24, Serial0/0/0

  26. TUFAN says:

    I have a final exam tommorow, should I study this one too? or do I need to study the 3 versions of final exam? pls answer me as quickly as possible

  27. Armando says:

    Thak’s so much. You save me

  28. lewis says:

    how much will i score out of this?

  29. lewis says:

    i have scored 96 thanks alot

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s